Công ty TNHH công nghệ số Tân Thành

Bộ điều khiển hiển thị cân, Schenck weighing display controller VEG20610/VDB20600

Bộ điều khiển hiển thị cân, Schenck weighing display controller VEG20610/VDB20600

  • Đăng ngày 17-01-2019 10:09:18 PM - 531 Lượt xem
  • Mã sản phẩm: Schenck VEG20610/VDB20600
  • The heavy control instrument is a dynamic belt scale and batching control instrument based on microcomputer. Using human-machine dialogue on the VFD screen, the weighing flow is directly displayed in Chinese form, and the relevant information is accumulated. Operation and calibration are especially convenient. The instrument has automatic zero calibration, automatic interval calibration, fault alarm automatic diagnosis, optical isolation input / output, standard serial port, built-in PID control output.

    Tình trạng sản phẩm:

    2, environmental parameters
      1. Storage temperature - 40 ° C - +70 ° C;
         Operating temperature -10 ° C - +50 ° C;
      2. Maximum relative humidity: 95%
    3, the power supply
      220VAC+10%~—15% 50Hz
      Fuse 0.5A
      EMI/RFI filter
    4, weighing sensor
         The instrument provides 10VDC, 200mA excitation power supply, and can be connected in parallel with 4 load cells.
         Sensitivity, 0.5mV/V-3.5mV/V
         Maximum input signal 33mV
         Load cell shield grounding
         Use the excitation compensation circuit jumper to select local or remote compensation when the cable distance is greater than 60 meters (not more than 900 meters)
    5, the motherboard digital input port
       The instrument main board provides three programmable input ports to receive dry contact switch signals.
    6, the motherboard digital output port
       The instrument main board provides 3 programmable output ports and 24VDC open collector output, which can directly drive the control relay.
    7, communication board
       The instrument can be equipped with a communication board. It can use standard RS-232, RS-485 serial interface and host computer communication board to collect instrument data and operate the instrument, and has two-way communication function.
    8, the main performance
    Four lines display, select through menu
     5 status indicators
     Current output of material flow or load
     Pulse output of total material weight
     Automatic zero adjustment
     Automatic zero tracking
     Photoelectrically coupled digital inputs and outputs
    Alarm and fault prompts
    Communication function: RS232, RS485 multi-station communication network
    One way process control mode: PID control output
    9, the main function
        All functional software is solidified in the memory chip. When the user installs an optional expansion board or the operator selects through the keyboard, the controller will automatically open the corresponding function.
       (1) Measurement function
         a, instantaneous flow calculation 
        The load cell output unit weight signal is multiplied by the speed sensor output unit belt speed signal. This result is instantaneous flow.
         b, weight accumulation
    The cumulative amount is the total weight of the unit length and the running length, and then converted into engineering units.
    C, automatic zero adjustment and automatic adjustment interval
    By defining the number of belt turns and belt length is the basis for automatic zero adjustment and automatic adjustment interval.
        To accurately calculate the length of the belt, the controller calculates the number of pulses from the speed sensor. When the required number of pulses is accumulated, the controller ends the calibration test, compares the theoretical value with the actual value, and calculates the calibration constant.
         d. Automatic zero tracking  
        When the belt is running, the flow rate is lower than the predetermined value, and the controller performs automatic zero adjustment according to the following steps.
        -- Wait for half of the test cycle (“Z” will be displayed)
        - Complete a zero test
        - Complete automatic zeroing of a test cycle
        - As long as the flow value is lower than the automatic zero tracking tracking value, the meter will repeat the above steps
    e, one input, two current output signals
        Optional input/output expansion board for one voltage/current input and two current output signals
    (2) Monitoring function
        Status prompt
        Process alarm
        Setting error
        Equipment failure
        High flow, low flow, high load, low load alarm
    (3) Automatic control of feeding function 
        The weighing controller provides an independent control current loop. The control current loop is usually used to control the feed amount. The control method is
        —— PID=proportional + integral + differential
        The controllable process variable is the feed amount, and the flow setting can be set via keyboard input or external analog signal. The control output is a 4-20 mA current loop.




    • Sản phẩm, hàng hóa chính hãng.
    • Giá cả cạnh tranh.
    • Dịch vụ chăm sóc khách hàng tận tâm.

    Thông Tin Công Ty

    Đã thông báo


    Trụ sở: Số 243 (số 2/185) Đường Chùa Láng, tổ 11, Phường Láng Thượng, Quận Đống Đa, Thành phố Hà Nội
    VPĐD: 37/213 Thiên Lôi-Vĩnh Niệm-Lê Chân-HP
    Kinh doanh 1: 0944.427.299
    Kinh doanh 2: 0787.971.515
    Kinh doanh 3: 0877.971.515
    Kinh doanh 4: 0816.861.515 
    Kinh doanh 5: 0836.861.515 
    Kinh doanh 6: 0917.971.515
    Website: http://tanthanhtech.com
    Website: http://diencongnghieptanthanh.com
    Website: http://tanthanh-automation.com
    Website: http://thietbitudongtanthanh.com
    Website: https://vienthongtanthanh.com
    Email: kinhdoanhtanthanhhn@gmail.com

  • Kết nối với chúng tôi